HEPA-grade duct cleaning that restores airflow and cuts energy waste
Industrial Air Duct Cleaning in camarilo for factories and warehouses
Industrial Air Duct Cleaning in camarilo is built for plants, warehouses, and shops that cannot afford dirty ductwork. We pull dust, debris, and mold out of sheet metal and flexible duct runs, then verify airflow with a blower door and duct inspection camera. If your registers are spitting grit or your HVAC is straining, call Fix Edge Works at (844) 796-2017.
Live phone supportUpfront optionsBacked workmanship
What's included
What our industrial duct cleaning includes
Every camarilo industrial job includes inspection, mechanical cleaning, HEPA extraction, and a written airflow report. Add-ons like coil cleaning, dryer vent service, or duct insulation repair are quoted separately once we see the system.
Full duct inspection with camera
We run a duct inspection camera through main trunks and branch runs and log every register grille. You see the footage before we clean, so there is no argument about what was in there.
Mechanical cleaning of all runs
Rotary brush systems, air whips, and compressed air nozzles work every accessible run. We clean sheet metal duct and flexible duct alike, including the corners a vacuum alone cannot reach.
HEPA vacuum and containment
Negative air machines and HEPA vacuum units hold the system under vacuum for the entire job. Nothing we loosen ends up on your production floor or in your break room.
Mold and pest treatment
Where we find mold growth in ducts or pest debris, we apply an EPA-registered treatment and a fogger pass. We also seal entry gaps with mastic and duct sealant so the problem does not return.
Airflow verification report
We re-measure static pressure and CFM after cleaning and hand you a written report with before-and-after numbers and photos. That report is your baseline for the next cleaning interval.
Service overview
What Industrial Air Duct Cleaning in camarilo actually involves
Industrial Air Duct Cleaning in camarilo is the mechanical removal of dust, debris, mold, and pest waste from large commercial duct systems, followed by HEPA filtration and airflow verification. On a factory or warehouse system, that means negative air machines holding the duct under vacuum while rotary brush systems and air whips break loose buildup from sheet metal duct walls. We seal every register grille and vent cover before we start so dust does not migrate into your production floor.
Camarilo sits in a coastal-influenced valley where spring pollen, summer dust, and fall Santa Ana winds all push particulate into intake louvers. Manufacturing plants and packing houses around Pleasant Valley and Somis pull that load straight into their ductwork. If you have been searching for industrial air duct cleaning in camarilo California near me, the real question is whether your static pressure has climbed enough to shorten motor life. We measure that before we quote.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
Our industrial duct cleaning process, step by step
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and mapping
We run a duct inspection camera through main trunks and branch runs, log every register grille, and measure static pressure at the air handler. On a 40,000 sq ft warehouse this takes two to three hours. You get photos of the worst runs before we touch anything.
Containment setup
We seal supply and return openings and stage negative air machines at the trunk access points. HEPA filtration runs the entire job so nothing escapes into your production space. Setup on a typical camarilo factory floor takes about 90 minutes.
Mechanical agitation
Rotary brush systems and air whips travel each run, breaking loose compacted dust from sheet metal and flexible duct walls. Compressed air nozzles reach corners a brush cannot. A 200-foot trunk line usually takes four to six hours to clean properly.
HEPA extraction and treatment
Everything we loosened gets pulled into the HEPA vacuum and captured. Where we find mold growth in ducts or pest debris, we apply an EPA-registered treatment and a fogger pass. This stage runs two to four hours depending on how many problem runs we found.
Verification and airflow report
We re-measure static pressure, compare before and after readings, and walk you through the duct inspection camera footage. You get a written report with photos, CFM numbers, and a filter replacement schedule. Most camarilo jobs wrap in one working day.
Tools & methods
Tools and methods we use on industrial ducts
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Negative air machine
Holds the entire duct system under negative pressure during cleaning so loosened debris cannot escape into your building.
HEPA vacuum
Captures fine particulate down to 0.3 microns at the collection point. Standard on every industrial job we run.
Rotary brush system
Breaks compacted dust off sheet metal duct walls in large-diameter trunks where a vacuum alone will not cut it.
Air whip and compressed air nozzle
Reaches corners, transitions, and branch takeoffs that a rotating brush cannot physically touch.
Duct inspection camera
Documents contamination before cleaning and verifies results after. You see the footage on every job.
Blower door
Measures system leakage and helps us confirm that duct sealing actually reduced air loss.
Fogger
Applies EPA-registered treatment evenly through problem runs where mold growth in ducts or pest debris was found.
Use cases
When camarilo facilities call us
These examples show how the service framework adapts rather than forcing every call through one repair.
Mission Oaks warehouse return system
Rodent activity in the return chase above the break room. Droppings and nesting debris were visible on camera, and employees reported a musty odor every morning. → Full HEPA containment removal, EPA-registered treatment, and mastic sealing of every entry gap. Two months later, no droppings, no odor, and the camera footage confirmed sealed points.
Camarillo Heights manufacturing plant
Failed internal air quality audit after workers reported musty odors. Camera inspection found mold growth in ducts along two return runs where condensation had been collecting for years. → Treated both runs with an EPA-registered product, resealed leaking joints, and replaced torn duct insulation. Follow-up audit passed, and odors cleared within a week of the work.
Problems we solve
Industrial duct problems we solve in camarilo
Most camarilo industrial duct complaints trace back to one of these four issues. We diagnose with instruments, not guesses.
Reduced HVAC airflow across the plant
We measure static pressure at the air handler, camera the worst runs, then mechanically clean the system back to design airflow. Most camarilo plants recover 20 to 40 percent of lost CFM in a single visit.
Dust and debris buildup in ducts
Rotary brush systems and air whips break the layer loose while negative air machines hold containment. We finish with HEPA extraction so the debris leaves the building instead of settling back down.
Musty odors from vents
We locate the moisture source with the inspection camera, treat the affected runs with an EPA-registered product, and seal the duct so condensation stops feeding the growth.
Pest infestation in ducts
We remove the debris under HEPA containment, treat the runs, and seal every entry gap with mastic and duct sealant. Then we show you the sealed points on camera so you know the fix is real.
Pricing process
What industrial duct cleaning costs in camarilo
$1,800 - $9,500 depending on scope
Total duct length
Price scales with linear feet of trunk and branch run. A 200-foot single trunk is a different job than 1,200 feet of multi-branch distribution across a plant.
Access and height
Rooftop units, ceiling plenums, and tight chases add labor. Easy ground-level access keeps the number down; scaffolding or lift work pushes it up.
Contamination level
Heavy dust and debris buildup takes more agitation passes. Mold growth in ducts or pest infestation adds treatment time and product cost.
How much does industrial air duct cleaning cost in camarilo California?
Most camarilo industrial jobs run $1,800 to $9,500 in 2026, depending on duct length, access, and contamination level. A single-trunk warehouse system with good access sits at the low end. Multi-story plants with rooftop units, heavy mold growth in ducts, or pest infestation push toward the top. We measure static pressure and camera-inspect before quoting, so the number you get is the number you pay.
How often should factory air ducts be cleaned in camarilo?
Most camarilo factories should clean main duct runs every 12 to 24 months. Add a cleaning if you process wood, metal, food, or textiles, because those operations load ductwork faster. Facilities near Somis and Santa Rosa Valley deal with more airborne dust and often land on the 12-month side. We set your interval based on measured static pressure rise, not a calendar guess.
Does industrial air duct cleaning require special certifications in camarilo?
California does not license duct cleaning as a standalone trade, but industrial work should be done by a C-20 HVAC licensed contractor using NADCA-trained technicians. Our crew holds NADCA Air Systems Cleaning Specialist training and OSHA 10-Hour Construction certification. For any job disturbing painted surfaces on older buildings, we also work under EPA Lead-Safe Certification practices.
Who offers industrial air duct cleaning near me in camarilo California?
Fix Edge Works serves camarilo and the surrounding valley from Old Town Camarillo out to Somis and Santa Rosa Valley. We handle factory air duct cleaning camarilo California wide, plus warehouse and commercial systems. Call (844) 796-2017 and we will schedule an inspection, usually within two business days, and give you a written airflow report after the work.
Related services
Related Services
Air Duct Cleaning Near Me
Same industrial-grade cleaning for smaller commercial spaces around camarilo. If your shop or office system is under 10,000 CFM, this is the right scope and the right price point.
24/7 Air Duct Cleaning
Round-the-clock dispatch for camarilo plants running three shifts. When a duct failure threatens production, we roll a crew out at 2 a.m. the same way we do at noon.
Emergency Air Duct Cleaning
For pest infestations, mold discoveries, or airflow collapse that stops a line. We contain the problem, clean the affected runs, and get your system back online fast.Ready when you are
Schedule Industrial Air Duct Cleaning in camarilo today
Dirty ductwork costs you airflow, energy, and worker comfort every shift. We inspect, clean, and verify with real numbers. Call (844) 796-2017 and we will get your camarilo facility on the schedule, usually within two business days.
Talk with the local team
Request Industrial Air Duct Cleaning
Call (844) 796-2017 or email info@fixedgeworks.com and we will get you on the schedule. Our office is open Monday through Friday, 8 a.m. to 6 p.m., and the emergency line runs 24/7. Most Camarillo calls get a same-day or next-day appointment. We confirm every booking by text and send a photo of your technician before arrival.